Call Today

 

 

They are making a few great pointers on the subject of A Step-by-Step Guide to Installing a Bathtub in general in this post underneath.

Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily available, the job can relocate quickly; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the work and are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you mount a brand-new tub in your shower room if you have already purchased a new tub as well as don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist should consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Installation

To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.

 

 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the limited accessibility that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Before proceeding to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Setting up the Tub

Using both wood boards under its feet, put the tub in the needed position. The wooden boards are useful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bath tub until the spirit level reviews degree.
To install faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally examine the overflow outlet and also the typical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been made use of a minimum of once as this will certainly settle it into its last position.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I was made aware of that editorial about Installing A Bathtub through a good friend on another site. Those who enjoyed reading our blog entry if you please make sure you remember to share it. We enjoy reading our article about How to Install a Bathtub.

Call Us Today